Home Fault Codes

Maytag Range Error Code 4d41: Meaning and Fix

4d41
How 4d41 appears on a Maytag range display.
Maytag range Inverter (part number W10217711), the component to check for code 4d41 (shared reference photo for this part type)
Product photo courtesy of AppliancePartsPros.com

Reading the range display

On a range or oven the fault appears on the clock or oven display, often with a beep. Press Cancel or Clear once to silence it, and write the code down first. Maytag shares the Whirlpool pairing: read the first group, then the sub-code that follows it.

Maytag appliances are built by Whirlpool Corporation on shared platforms, which is why Maytag codes often match Whirlpool ones. Maytag washers, dryers and ranges commonly show F-codes with an E sub-code, or flashing keypad lights. The codes apply to model numbers such as MDB7600AWB, MDB7600AWW and PYE2300AYW; check the label on your unit to confirm yours.

What causes 4d41

How to fix it

  1. Cycle the power: turn the range or oven breaker off for one minute, switch it back on, and run the function that showed the code.
  2. Before opening any panel, switch off the breaker or unplug the appliance; this circuit can carry line voltage.
  3. Check that the doors seal and nothing keeps them from closing; look for frost build-up on the back wall of the freezer.
  4. Listen for the evaporator and condenser fans and confirm both turn freely.
  5. Unplug the unit with the doors open for several hours to melt any frost fully, then restart and watch temperatures over 24 hours.
  6. If frost returns, test the defrost heater, sensor and fans in turn and replace the one that fails; call a technician for sealed-system faults.
  7. Run a full short cycle or function again and confirm the code stays gone before putting the appliance back into normal use.

Parts you may need

PartPart no.Buy
InverterW10217711Find part

Part numbers are OEM references; confirm fit by your model number before ordering. Some links are affiliate links; we may earn a commission at no extra cost to you.

Questions

What does 4d41 mean on a Maytag range or wall oven?

It is a fault code from the Maytag control. It indicates a problem with the cooling system. A power reset is the first thing to try.

Can I keep using the range or wall oven while it shows 4d41?

Stop using it until it has been checked. This fault involves heat, high voltage or sealed-system parts, and running it can damage the appliance or create a safety risk.

Do I need a technician to clear 4d41?

Often yes. Part of this repair means testing live circuits or replacing a control board, so a technician is the safer choice unless you are comfortable with electrical diagnosis.

Other Maytag range codes

Maytag range Control Assembly Lcx (part number W11567368), the component to check for code 1c2c1c2cControl panel faultMaytag range Oven Temperature Sensor (part number 12001656), the component to check for code 1d111d11Temperature sensor faultMaytag range Oven Temperature Sensor (part number 12001656), the component to check for code 1d21 (shared reference photo for this part type)1d21Temperature sensor faultMaytag range Oven Temperature Sensor (part number 12001656), the component to check for code 1d22 (shared reference photo for this part type)1d22Temperature sensor faultMaytag range Oven Temperature Sensor (part number 12001656), the component to check for code 3d11 (shared reference photo for this part type)3d11Temperature sensor faultMaytag range Oven Temperature Sensor (part number 12001656), the component to check for code 3d12 (shared reference photo for this part type)3d12Temperature sensor fault

Sources

Part numbers are OEM references; confirm fit by your model number before ordering. Meanings compiled from manufacturer and parts-retailer documentation; see sources below. Unplug the appliance before opening it.

Applies to models including MER5755QAW, MER5770AAW, MER6770AAW, MGR5750ADW, MER5730AAW, MER5550AAW, CRE9600CCE, MER5755QAB.