Amana Dryer Error Code F4 E3: Meaning and Fix

How F4 E3 appears on a Amana dryer display.

Amana dryer Timer (part number W10857612), the component to check for code F4 E3 (shared reference photo for this part type) — Product photo courtesy of AppliancePartsPros.com

Also shown as: F4E3, F4-E3

Reading the dryer display

On a dryer the code shows in the time-remaining window or as blinking status lights. Write down the characters before you press anything, because starting a new cycle usually clears the display. Amana models often flash lights instead of printing text, so count the flashes.

Amana is a Whirlpool Corporation brand sold mostly through builder and value channels. Its entry-level washers, dryers and ranges use the simpler Whirlpool-family control boards, so the codes are short and often shown as flashing lights. The codes apply to model numbers such as ADB1200AWS, ADB2200AWS and NDE2330AYW; check the label on your unit to confirm yours.

What causes F4 E3

Drain hose or standpipe is kinked, clogged or set too high
Too much detergent created suds that the pump cannot clear
Drain pump motor is failing or its wiring is loose
Pump filter or impeller is jammed with lint, coins, glass or debris

How to fix it

Cycle the power: switch off the dryer breaker (or unplug it) for one minute, restore power, then start a timed dry cycle and watch for the code.
Switch the power off and check the drain hose for kinks and make sure the standpipe or disposal knockout is clear.
Open the pump filter or access panel with a towel and tray ready, and remove anything blocking the pump.
Run a rinse-and-spin or drain cycle and watch whether water leaves; a humming pump that does not move water points to a seized impeller.
Replace the drain pump if it is jammed beyond clearing or its motor will not run when power is applied.
Run a full short cycle or function again and confirm the code stays gone before putting the appliance back into normal use.

Parts you may need

Part	Part no.	Buy
Timer	W10857612	Find part

Part numbers are OEM references; confirm fit by your model number before ordering. Some links are affiliate links; we may earn a commission at no extra cost to you.

Questions

What does F4 E3 mean on a Amana dryer?

It is a fault code from the Amana control. It indicates a problem with the drain system. A power reset is the first thing to try.

Can I keep using the dryer while it shows F4 E3?

You can try it after a power reset. If the code returns, the affected function may not run properly, so it is worth fixing soon before it causes a bigger failure.

Do I need a technician to clear F4 E3?

Many owners can fix it themselves. Start with the reset and the inspection steps, and only call a technician if the part tests bad and you do not want to replace it.

Other Amana dryer codes

Amana dryer Timer (part number W10857612), the component to check for code 0E

0EControl electronics fault

Amana dryer Timer (part number W10857612), the component to check for code 0g (shared reference photo for this part type)

0gControl electronics fault

Amana dryer Timer (part number W10857612), the component to check for code 3E (shared reference photo for this part type)

3EControl electronics fault

Amana dryer Timer (part number W10857612), the component to check for code 6E (shared reference photo for this part type)

6EControl electronics fault

Amana dryer Timer (part number W10857612), the component to check for code E1 (shared reference photo for this part type)

E1Control electronics fault

Amana dryer Timer (part number W10857612), the component to check for code E2 (shared reference photo for this part type)

E2Control electronics fault

Sources

Part numbers are OEM references; confirm fit by your model number before ordering. Meanings compiled from manufacturer and parts-retailer documentation; see sources below. Unplug the appliance before opening it.

Applies to models including NDE2330AYW, NDE2335AYW, NDE7800AYW, NDG2330AWW, NDG7800AWW, NDE5800AYW.