Home Fault Codes

Maytag Washer Error Code F7 E9: Meaning and Fix

F7 E9
How F7 E9 appears on a Maytag washer display.
Maytag washer Cntrl Board Dryer (part number WPW10476828), the component to check for code F7 E9 (shared reference photo for this part type)
Product photo courtesy of AppliancePartsPros.com

Also shown as: F7E9, F7-E9

Reading the washer display

On a washer the code appears on the digital display or as a pattern of flashing cycle lights. Note it exactly, including any dashes or sub-codes, then unplug the washer for five minutes and run a short drain cycle to see whether it returns. Maytag shares the Whirlpool pairing: read the first group, then the sub-code that follows it.

Maytag appliances are built by Whirlpool Corporation on shared platforms, which is why Maytag codes often match Whirlpool ones. Maytag washers, dryers and ranges commonly show F-codes with an E sub-code, or flashing keypad lights. The codes apply to model numbers such as MDB7600AWB, MDB7600AWW and PYE2300AYW; check the label on your unit to confirm yours.

What causes F7 E9

How to fix it

  1. Cycle the power: unplug the washer (or switch off its breaker) for five minutes, restore power, then start a short cycle and see whether the code returns.
  2. Disconnect power for the recommended time, then restart and press each key to see if one sticks.
  3. Clean the panel with a barely damp cloth and check around the keys for spills or swelling.
  4. With power off, reseat the ribbon cable or harness between the panel and the main control.
  5. Replace the user interface or touchpad if the code returns, then confirm every key responds.
  6. Run a full short cycle or function again and confirm the code stays gone before putting the appliance back into normal use.

Parts you may need

PartPart no.Buy
Cntrl Board DryerWPW10476828Find part

Part numbers are OEM references; confirm fit by your model number before ordering. Some links are affiliate links; we may earn a commission at no extra cost to you.

Questions

What does F7 E9 mean on a Maytag washer?

It is a fault code from the Maytag control. It indicates a problem with the control panel. A power reset is the first thing to try.

Can I keep using the washer while it shows F7 E9?

You can try it after a power reset. If the code returns, the affected function may not run properly, so it is worth fixing soon before it causes a bigger failure.

Do I need a technician to clear F7 E9?

Many owners can fix it themselves. Start with the reset and the inspection steps, and only call a technician if the part tests bad and you do not want to replace it.

Other Maytag washer codes

Maytag washer Cntrl Board Dryer (part number WPW10476828), the component to check for code 1h, 2h, 3h....up to 12h1h, 2h, 3h....up to 12hControl panel faultMaytag washer Cntrl Board Dryer (part number WPW10476828), the component to check for code Err (shared reference photo for this part type)ErrControl panel faultMaytag washer Pump Assembly (part number WP3363394), the component to check for code F0 E2F0 E2Drain system faultMaytag washer Cntrl Board Dryer (part number WPW10476828), the component to check for code F0 E3 (shared reference photo for this part type)F0 E3Control panel faultMaytag washer Valve (part number W11165546), the component to check for code F0 E4F0 E4Water fill circuit faultMaytag washer Valve (part number W11165546), the component to check for code F0 E5 (shared reference photo for this part type)F0 E5Water fill circuit fault

Sources

Part numbers are OEM references; confirm fit by your model number before ordering. Meanings compiled from manufacturer and parts-retailer documentation; see sources below. Unplug the appliance before opening it.

Applies to models including MAH4000AWW, PAV2300AWW, MAH5500BWW, MAH3000AWW, FAV6800AWW, MAH8700AWW, MAV6200AWW, PAVT234AWW.