Home Fault Codes

Kenmore Dishwasher Error Code F2E1: Meaning and Fix

F2E1
How F2E1 appears on a Kenmore dishwasher display.
Kenmore dishwasher control board part photo, the component usually involved when F2E1 (stuck key / keypad (whirlpool-built)) appears
AppliancePartsPros.com product photo

Also shown as: F2-E1

Reading the dishwasher display

A dishwasher reports its fault in the display window, or by blinking a cycle light a set number of times with a pause between groups. Count the blinks and pauses before opening the door. Check the model-number prefix first: the same Kenmore code can mean different things depending on the manufacturer.

Kenmore is a private label, and the factory that built your unit decides which fault codes it shows. The first digits of a Kenmore model number (110, 417, 665, 795, 796 and so on) tell you whether Whirlpool, LG, Electrolux or Frigidaire made it. Check the model label on your unit before using any chart.

What causes F2E1

How to fix it

  1. Press each button once, firmly, to free anything sticky, and wipe the panel with a barely damp cloth.
  2. Unplug the machine for five minutes and plug it back in.
  3. Open the inner door panel and dry the keypad contacts.
  4. Open the console and check that the ribbon cable to the interface board is fully seated and dry.
  5. Look for liquid damage or burned tracks on the interface board.
  6. Replace the touch panel or UI board if the code persists after a reset.

Parts you may need

PartPart no.Buy
Dishwasher Main Control Board5304514670Find part

Part numbers are OEM references; confirm fit by your model number before ordering. Some links are affiliate links; we may earn a commission at no extra cost to you.

Questions

What does error F2E1 mean on a Kenmore dishwasher?

A touch pad reads as pressed constantly, so the control flags a keypad fault. Kenmore sells units built by several manufacturers, so the code table that applies depends on who made your model; use the model number to confirm.

Can I keep using my dishwasher while F2E1 is showing?

Usually yes if the buttons you need still respond, but erratic key signals can start or stop cycles on their own.

How do I clear F2E1, and can I fix it myself?

Cancel the program, switch the appliance off and leave it unplugged (or the breaker off) for about five minutes, then restart. The code only stays cleared if the underlying problem is fixed, so work through the steps above. Parts here involve electronics, heating or sealed components, so consider a qualified technician if the basic checks do not clear it.

Other Kenmore dishwasher codes

Kenmore dishwasher control board part photo, the component usually involved when F1E1 (electronic control failure (whirlpool-built)) appearsF1E1Electronic control failure (Whirlpool-built)Kenmore dishwasher control board part photo, the component usually involved when F2E2 (keypad fault (whirlpool-built)) appearsF2E2Keypad fault (Whirlpool-built)Kenmore dishwasher thermistor part photo, the component usually involved when F3E1 (thermistor open (whirlpool-built)) appearsF3E1Thermistor open (Whirlpool-built)Kenmore dishwasher thermistor part photo, the component usually involved when F3E2 (thermistor shorted (whirlpool-built)) appearsF3E2Thermistor shorted (Whirlpool-built)Kenmore dishwasher thermistor part photo, the component usually involved when F3E3 (thermistor out of range (whirlpool-built)) appearsF3E3Thermistor out of range (Whirlpool-built)Kenmore dishwasher water inlet valve part photo, the component usually involved when F4E1 (fill problem (whirlpool-built)) appearsF4E1Fill problem (Whirlpool-built)

Sources

Part numbers are OEM references; confirm fit by your model number before ordering. Meanings compiled from manufacturer and parts-retailer documentation; see sources below. Unplug the appliance before opening it.

Applies to models including Kenmore Elite 665 series (Bosch/Whirlpool/Electrolux-built), Kenmore 665.1 series (Whirlpool-built), Kenmore 630 / 665.13 series (Electrolux-built).